A beautiful pearl-encrusted mannequin torso like the one above is super easy to create. The only skill needed is patience because it is a little time-consuming. But the result is so worth it!
It is a very creative way to repurpose pearls from broken pieces of jewelry (along with any other beads, buttons, or shiny objects). And you end up with a beautiful art piece for your home or retail store.
The design team at Mannequin Madness collaborated on tricks and tips to make the process of making this as easy as possible. When we posted a similar one on Facebook it got TONS of likes so we knew that this struck a nerve with crafters. But that one was so intricate it was not very easy for a beginning crafter. And it required a lot more materials than most people have on hand.
So, we came up with our “hack” version which takes less time, has fewer materials, and can be done in a relatively short period of time. We like to offer projects at Mannequin Madness that can be made by people of all crafting levels.
Here are the supplies and steps needed.
- A female mannequin torso. The torso can bemade of cloth, fiberglass or plastic. But we recommend a torso that is three dimensional, not the torsos the are just a shell with a hollow back, l like this STYLE. (NOTE you can save money and buy a USED versus NEW torso. We have a selection HERE.
- A small t shirt that is stretchy because it is made out of jersey, not cotton. Otherwise the shirt will not fit tight on the torso which is what you MUST have. You can also use a swimsuit, corset, tube top or bra. The reason for using a t-shirt or other fabric is it makes it much easier for the glue to adhere to the form. And if by chance you don’t like your finished product, you can remove the garment and start over.
- A HIGH-heat glue gun (Be sure it’s high-heat, a low heat glue gun dries too fast) and plenty of glue sticks
- Painter’s or masking tape to mark off the beading areas for your design.
- Pearls, beads, buttons, jewelry, etc.– If you don’t have enough broken or discarded pieces of your own jewelry you can supplement by buying jewelry at a thrift store. Or buy a string of beads at a craft store. This is also a good way to repurpose Mardi Gras beads. Remember, the larger the beads, the less glueing you have to do!
- We also used rhinestone covered ribbon called “faux jewel diamond wrap” which looks like this:
- Pull the stretchy t-shirt (or other garment) over the torso and make sure it is a tight fit. You can use pins, iron-on tape or hand sew it to ensure it is a tight fit. If the shirt has sleeves, cut them off at the armpit and reserve them for making a choker which we will describe below.
- Take the painter’s tape and mark of the areas that you want to bead. The painter’s tape will hep you maintain a symmetrical look if that is desired. Using the glue gun begin beading one marked-off area with loose or strung beads. You’ll get different effects for each. Add buttons and other adornments to get the look you want.
- Move onto another marked off area until the torso is as covered as you wish. It might be easier to put the torso on its back as you work.
- You might find that you will change your mind about your design as you work. When we first started the plan was to use only pearls and rhinestone-covered ribbon. But since we didn’t have enough pearls, we used our leftover pink beads from Mardi Gras.
- You can create a choker necklace with the leftover material of sleeves from the t-shirt. Just put the fabric over the neck of the torso and make it fit snug and then embellish.
- When the front is as complete as you want it to be, cover the arm holes on each side with a beads.Beading the back of the form is optional. Since ours was going to be displayed against a wall, we didn’t bead it.
As a finishing touch, we glued a crown to the neck cap. You could also glue more beads, silk flowers, or a drapery finial. And we put the form on a tabletop height stand and made a skirt for it out of tulle and deco mesh. A petticoat would achieve a similar effect. The form was just too pretty to have a bare metal stand protruding underneath.
For a more dramatic effect for the skirt, do what we did for the Mardi Gras-themed beaded torso below.
We put the torso on a tall stand and made a skirt using chicken wire (you can also use a tomato cage) and decorated it with deco mesh and Mardi Gras garland. You can also do this idea for Xmas and use deco mesh and pine garland and attach your holiday ornaments.